Abstract
Carbon fiber-reinforced polymer (CFRP) composites are pivotal to equipment in Polar Regions, yet their long-term durability in this low-temperature marine environment is severely compromised by the synergistic degradation of coupled environmental factors. Traditional single-factor aging studies cannot replicate this complex scenario, leaving a critical gap in service life prediction. An accelerated aging protocol incorporating simultaneous hygrothermal, freeze-thaw, sub-zero freezing, and UV exposure was established to systematically investigate the degradation of T700 and T800 CFRP composite materials under simulated polar environments. Results reveal that failure is fundamentally dominated by the interface variation since matrix-relevant flexural and shear strengths decline drastically (up to 45%), whereas fiber-dominated Izod impact strength remains nearly intact. A synergistic degradation sequence is proposed: the process commences with interfacial stress induced by hygrothermal swelling, followed by damage propagation during freeze-thaw cycles, stress accumulation (locking) during sub-zero freezing, and is accelerated by UV radiation, which generates defects that facilitate moisture ingress. This work provides a scientific basis for material selection, durability prediction, and the design of robust marine composite structures.
Similar content being viewed by others
Data Availability
The raw/processed data required to reproduce these findings cannot be shared at this time as the data is related to an ongoing study.
References
Han, Y., Xu, Q., Wang, Y.-Q. & Gao, H. Bionic CFRP for extreme applications: from natural structures to high-performance manufacturing. Compos. Part B 311, 113193 (2026).
Hao, Z. et al. Mechanical characteristics and application of CFRP cable anchor support structures in coastal area. Ocean Eng. 299, 117366 (2024).
An, Q., Ming, W., Cai, X. & Chen, M. Effects of tool parameters on cutting force in orthogonal machining of T700/LT03A unidirectional carbon fiber reinforced polymer laminates. J. Reinf. Plast. Compos. 34, 591–602 (2015).
Luo, K., Chen, L. & Liang, W. Structural health monitoring of carbon fiber reinforced polymer composite laminates for offshore wind turbine blades based on dual maximum correlation coefficient method. Renew. Energy 201, 1163–1175 (2022).
Shao, Z., Liu, Z., Zhang, Y. & Zhu, X. Fatigue Life Prediction and Reliability Assessment of CFRP Adhesively Bonded Joints in Offshore Wind Turbine Blade Applications: A Physics-Informed Data-Driven Approach. Qual. Reliab. Eng. Int. 41, 943–956 (2025).
Shen, M.-Y., Guo, Z.-H. & Feng, W.-T. A study on the characteristics and thermal properties of modified regenerated carbon fiber reinforced thermoplastic composite recycled from waste wind turbine blade spar. Compos. Part B 264, 110878 (2023).
Wang, Q. et al. Structure design and ultimate strength envelope of a modular carbon fiber-reinforced polymer (CFRP) laminate tube box on a 5000 ft deep-sea ultra large unmanned underwater vehicle. Ocean Eng. 313, 119681 (2024).
Zhao, Q., Zhao, W. & Wu, Y. Constructing bi-functional Ce-MOF on carbon fiber endowing epoxy coating with excellent anti-corrosion and erosion wear resistance. Carbon 214, 14 (2023).
Zhang, X., Zhao, M., Xia, J. & Ge, T. Underwater implosion protection of a new concept composite structure for a deep-sea hollow ceramic sphere with CFRP shield. Ocean Eng. 306, 19 (2024).
Qin, Z. et al. Effect of Thickness on the Uniaxial Compression Failure Behavior of CFRP Laminates. Polymers 17, 2518 (2025).
Li, Y. et al. Cryogenic mechanics and damage behaviors of carbon fiber reinforced polymer composites. Compos. Part A 169, 16 (2023).
Liu, J. et al. Experimental study of notched tensile strength of large open-hole carbon fiber reinforced polymer laminates at low temperature. Compos. Commun. 39, 101546 (2023).
Vigón, P., Argüelles, A., Lozano, M. & Viña, J. Fracture analysis under modes I and II of adhesive joints on CFRP in saline environment. Npj Mater. Degrad. 8, 117 (2024).
Yu, H. & Xing, P. Moisture absorption characterization of carbon fiber-reinforced polymer using Fickian and non-Fickian models. Polym. Compos. 43, 8935–8946 (2022).
Xiang, Z. D. & Jones, F. R. Thermal-spike-enhanced moisture absorption by polymer-matrix carbon-fibre composites. Compos. Sci. Technol. 57, 451–461 (1997).
Korkees, F. Moisture absorption behavior and diffusion characteristics of continuous carbon fiber reinforced epoxy composites: a review. Polym. -Plast. Technol. Mater. 62, 1789–1882 (2023).
Zhong, Y. & Joshi, S. C. Initiation of structural defects in carbon fiber reinforced polymer composites under hygrothermal environments. J. Compos. Mater. 50, 1085–1097 (2016).
Pang, Y. Y., Wu, G., Wang, H. T., Su, Z. L. & He, X. Y. Experimental study on the bond behavior of the CFRP-steel interface under the freeze–thaw cycles. Thin-Walled Struct. 159, 107233 (2020).
Cao, Q., Xu, J., Wu, Z. & Zhang, L. Performance of damaged concrete stub columns strengthened with post-tensioned CFRP under freezing-thawing environment. Structures 47, 544–556 (2023).
Li, W., Liu, W., Xu, W. & Ji, Y. Durability Investigation on CFRP Strengthened Cementitious Materials in Cold Region. Polymers 14, 2190 (2022).
Li, K., Zhou, A., Liu, T., Zou, D. & Yu, Z. Long-term performance and deterioration mechanism of novel hydrophobic coated fiber reinforced composite in marine environment. Compos. Part A 190, 108716 (2025).
Sápi, Z. & Butler, R. Properties of cryogenic and low temperature composite materials – A review. Cryogenics 111, 103190 (2020).
Suo, H., Yiheng, W., Zhaohui, W., Cheng, H. & Luo, B. Modeling to investigate the mechanical degradation of carbon fiber-reinforced polymer composites subjected to salt-fog and ultraviolet radiation synergistic environment. J. Mater. Sci. 60, 5847–5868 (2025).
Jang, J. H. et al. Long-term properties of carbon fiber-reinforced shape memory epoxy/polymer composites exposed to vacuum and ultraviolet radiation. Smart Mater. Struct. 28, 115013 (2019).
Ding, J. C. Li. Experimental study on ultrasonic three-point bending fatigue of CFRP under ultraviolet radiation. Eng. Fract. Mech. 242, 107435 (2021).
Dong, S. et al. Durability of carbon- and glass-fiber reinforced thermoplastic polymer composites: A literature review. J. Build. Eng. 98, 111055 (2024).
Qin, G. et al. Influence of single or multi-factor coupling of temperature, humidity and load on the aging failure of adhesively bonded CFRP/aluminum alloy composite joints for automobile applications. Int. J. Adhes. Adhes. 123, 103345 (2023).
Peng, H., Zhou, T., Shangguan, L. & Cheng, R. Effect of Temperature and Humidity Coupling on the Ageing Failure of Carbon Fiber Composite/Titanium Bonded Joints. Polymers 16, 952 (2024).
Ma, He, Hui & Xu Effects of hygrothermal and thermal aging on the low-velocity impact properties of carbon fiber composites. Adv. Compos. Mater. 29, 55–72 (2020).
Zhou, S., XiongXu, Y. ao, LiangWang, LeiHui & Li Study on the damage behavior of carbon fiber composite after low-velocity impact under hygrothermal aging. J. Appl. Polym. Sci. 138, 50289 (2021).
Lei, Y., Kang, Z., Zhang, J., Sun, Y. & Zhang, B. Effect of freeze-thaw cycling on the mechanical properties of continuous carbon fiber-reinforced polyamide 6 composites. Polym. Test. 114, 107704 (2022).
Chiang, Z. F. P. Experimental investigation of the synergistic effects of moisture and freeze-thaw cycles on carbon fiber vinyl-ester composites. J. Compos. Mater. 52, 919–930 (2018).
Tan, C., Jiang, X., Qiang, X. & Fan, M. Flexural Performance of Carbon Fiber-Reinforced Polymer Prestressed Spun High-Strength Concrete Pile. Appl. Sci. 14, 7170 (2024).
Scott, P., Toumpanaki, E. & Lees, J. M. Solution Uptake in Cylindrical Carbon-Fibre-Reinforced Polymer (CFRP) Tendons. Adv. Polym. Technol. 16, 1981256 (2022).
Meng, M., Rizvi, M. J., Le, H. R. & Grove, S. M. Multi-scale modelling of moisture diffusion coupled with stress distribution in CFRP laminated composites. Compos. Struct. 138, 295–304 (2016).
Kang, C. et al. Experimental investigation of friction between prepreg tape and compaction roller for prepreg tape hoop winding. J. Reinf. Plast. Compos. 37, 853–862 (2018).
Murdy, P. et al. Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites. J. Mar. Sci. Eng. 13, 1790 (2025).
Ofoegbu, S. U., Quevedo, M. C., Bastos, A. C., Ferreira, M. G. S. & Zheludkevich, M. L. Electrochemical characterization and degradation of carbon fibre reinforced polymer in quiescent near neutral chloride media. npj Mater. Degrad. 6, 49 (2022).
Wang, Y., Meng, Z., Zhu, W., Wan, B. & Bai, Y. Hygrothermal aging behavior and aging mechanism of carbon nanofibers/epoxy composites. Constr. Build. Mater. 294, 123538 (2021).
Moghimi-Ardekani, A., Ivens, J. & Vuure, A. W. V. Fatigue behaviour of flax fibre reinforced thermoset composites under hygrothermal conditions. Int. J. Fatigue 200, 109114 (2025).
Jinhao, W. et al. Study on tensile properties of carbon fiber reinforced AA7075 composite at high temperatures. Mater. Sci. Eng. A. 825, 141931 (2021).
Yang, Y., Jiang, Y., Liang, H., Yin, X. & Huang, Y. Study on Tensile Properties of CFRP Plates under Elevated Temperature Exposure. Materials 12, 1995 (2019).
Jiang, F. et al. Effect of freeze-thaw cycles on tensile properties of CFRP, bond behavior of CFRP-concrete, and flexural performance of CFRP-strengthened concrete beams. Cold. Reg. Sci. Technol. 194, 103461 (2022).
Yu, H., Zhao, H. & Shi, F. Bending Performance and Reinforcement of Rocker Panel Components with Unidirectional Carbon Fiber Composite. Materials 12, 3164 (2019).
Jin, L. et al. Size effect in shear failure of RC beams reinforced with CFRP sheets: Influences of CFRP adhesion angle and shear-span ratio. Eng. Struct. 326, 119543 (2025).
Vitale, P., Francucci, G. M., Rapp, H. & Stocchi, A. L. Shear response of ultra-lightweight CFRP cores. Elsevier 238, 111879 (2020).
Federation, C.B.M. Fiber-reinforced plastics composites-Determination of tensile properties. Vol. GB/T 1447-2005 (China, 2005).
Federation, C.B.M. Fiber-reinforced plastics composites-Determination of compressive properties. Vol. GB/T 1448-2005 (China, 2005).
Council, C.N.T.a.A. Test method for bending properties of 3D braided fabric and its polymer matrix composites. Vol. GB/T 33621-2017 (China, 2017).
Federation, C.P.a.C.I. Plastics - Determination of izod impact strength. Vol. GB/T 1843-2008 (China, 2008).
Federation, C.B.M. Test method for short-beam shear strength of polymer matrix composite materials. Vol. GB/T 30969-2014 (China, 2014).
Acknowledgements
The authors wish to acknowledgement the financial support of the Natural Science Foundation of Shandong province (ZR2024JQ028), the Youth Innovation Plan of Shandong Province (2022KJ002), and the Project of Taishan Scholars (tsqn202312107).
Author information
Authors and Affiliations
Contributions
M.Z.: Conceptualization, Methodology Investigation, Writing-Original. W.L.: Validation, Formal Analysis. W.Y.: Methodology, Validation. W.W.: Software. J.L.: Methodology Investigation, Validation. H.L.: Methodology Investigation. C.M.: Review & Editing. Z.C.: Review & Editing, Funding Acquisition, Supervision. All authors reviewed the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License, which permits any non-commercial use, sharing, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if you modified the licensed material. You do not have permission under this licence to share adapted material derived from this article or parts of it. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by-nc-nd/4.0/.
About this article
Cite this article
Zhang, M., Li, W., Yin, W. et al. Mechanical degradation of carbon fiber reinforced polymer composites under coupled multi-factor aging in a simulated polar environment. npj Mater Degrad (2026). https://doi.org/10.1038/s41529-026-00777-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41529-026-00777-w
