Table 10 NSGA-II suggested sets for input parameters, and response measures.
Run | Input parameters | Machining responses | ||||||
|---|---|---|---|---|---|---|---|---|
MT | IP | P | V | CS | MRR | |||
CS_Flat | CS_Curve | MRR_Flat | MRR_Curve | |||||
– | (A) | (mu) | (V) | (mm/min) | (mm/min) | (cm3/min) | (cm3/min) | |
1 | 1.86 | 4.00 | 56.42 | 100.00 | 2.953 | 2.481 | 130.501 | 196.143 |
2 | 1.45 | 4.00 | 55.93 | 94.38 | 3.903 | 2.227 | 108.518 | 142.035 |
3 | 2.00 | 4.00 | 56.01 | 99.99 | 2.797 | 2.476 | 139.872 | 197.821 |
4 | 1.45 | 3.98 | 55.97 | 95.57 | 3.849 | 2.300 | 109.489 | 151.155 |
5 | 1.91 | 4.00 | 56.15 | 97.07 | 3.212 | 2.393 | 125.681 | 172.838 |
6 | 1.84 | 3.99 | 56.01 | 96.08 | 3.398 | 2.344 | 118.762 | 161.891 |
7 | 1.45 | 4.00 | 55.93 | 94.63 | 3.900 | 2.245 | 108.784 | 144.055 |
8 | 1.64 | 3.94 | 56.24 | 97.00 | 3.577 | 2.405 | 112.700 | 165.260 |
9 | 1.60 | 4.00 | 55.93 | 96.08 | 3.719 | 2.366 | 111.299 | 159.176 |
10 | 1.83 | 3.93 | 55.96 | 97.13 | 3.301 | 2.400 | 120.537 | 169.089 |
11 | 1.71 | 3.98 | 55.89 | 95.05 | 3.668 | 2.291 | 111.502 | 150.317 |
12 | 2.00 | 4.00 | 56.70 | 99.99 | 2.786 | 2.476 | 139.643 | 196.816 |
13 | 1.88 | 3.98 | 55.99 | 98.94 | 3.030 | 2.462 | 128.967 | 188.937 |
14 | 1.85 | 3.97 | 56.16 | 97.61 | 3.220 | 2.423 | 123.161 | 175.878 |
15 | 1.46 | 4.00 | 56.00 | 98.11 | 3.597 | 2.372 | 111.841 | 177.531 |
16 | 1.42 | 4.00 | 56.07 | 97.03 | 3.722 | 2.328 | 110.729 | 166.017 |
17 | 1.23 | 4.00 | 56.82 | 99.49 | 3.516 | 2.208 | 111.357 | 185.338 |
18 | 1.84 | 3.99 | 55.73 | 95.30 | 3.448 | 2.283 | 116.872 | 155.408 |
