Abstract
Plastic waste represents an escalating environmental challenge and necessitates scalable processing strategies consistent with the United Nations’ Sustainable Development Goal 12 on responsible consumption and production. This work examines controlled hot pressing of polyethylene-based waste as a physical upcycling route for producing functional laminate sheets. Low-density polyethylene (LDPE), high-density polyethylene (HDPE), and polyethylene-coated polypropylene (PP/PE composite) were investigated, with processing temperature, pressure, and dwell time systematically analysed using an orthogonal experimental design. LDPE exhibited the most favourable forming behaviour, achieving continuous sheet formation at 120–130 °C under a nominal pressure of approximately 0.59 MPa with limited thickness variation. Relative to unprocessed films, hot-pressed materials displayed reduced surface friction and increased water contact angles, indicating decreased surface wettability under the applied conditions. Microscopic observations revealed modified surface morphology after processing, while elemental mapping showed no pronounced changes in macroscopic elemental distribution. HDPE achieved comparable consolidation, whereas PP/PE composites did not form continuous laminates. The results indicate that controlled hot pressing provides a low-energy and reproducible pathway for converting post-consumer polyethylene films into functional materials for circular applications.
Similar content being viewed by others
Data availability
Data is provided within the manuscript.
References
Singh, N. & Walker, T. R. Plastic recycling: a panacea or environmental pollution problem. Npj Mater. Sustain. 2, 17. https://doi.org/10.1038/s44296-024-00024-w (2024).
Pereyra-Camacho, M. A. & Pardo, I. Plastics and the sustainable development goals: from waste to wealth with microbial recycling and upcycling. Microb. Biotechnol. 17, 14459. https://doi.org/10.1111/1751-7915.14459 (2024).
Kalali, E. N. et al. A critical review of the current progress of plastic waste recycling technology in structural materials. Curr. Opin. Green. Sustain. Chem. 40, 100763. https://doi.org/10.1016/j.cogsc.2023.100763 (2023).
Sambyal, P. et al. Plastic recycling: challenges and opportunities. Can. J. Chem. Eng. 103, 2462–2498. https://doi.org/10.1002/cjce.25531 (2025).
Ragaert, K., Delva, L. & Van Geem, K. Mechanical and chemical recycling of solid plastic waste. Waste Manag. 69, 24–58. https://doi.org/10.1016/j.wasman.2017.07.044 (2017).
Schyns, Z. O. G. & Shaver, M. P. Mechanical recycling of packaging plastics: a review. Macromol. Rapid Commun. 42, 2000415. https://doi.org/10.1002/marc.202000415 (2021).
Müller, M., Kolář, V. & Mishra, R. K. Mechanical and thermal degradation-related performance of recycled LDPE from post-consumer waste. Polymers 16, 2863. https://doi.org/10.3390/polym16202863 (2024).
Saleem, J. et al. Valorization of mixed plastics waste for the synthesis of flexible superhydrophobic materials. Adv. Compos. Hybrid. Mater. 7, 11. https://doi.org/10.1007/s42114-024-00829-2 (2024).
Xiong, Z., Zheng, C. & Xia, Y. Polymer self-etching for superhydrophobicity through a green hot-pressing-exfoliation process: low and high adhesion. Macromol. Mater. Eng. 301, 653–658. https://doi.org/10.1002/mame.201500465 (2016).
Cassie, A. B. D. & Baxter, S. Wettability of porous surfaces. Trans. Faraday Soc. 40, 546–551. https://doi.org/10.1039/TF9444000546 (1944).
Nosonovsky, M. On the range of applicability of the Wenzel and Cassie equations. Langmuir 23, 9919–9920. https://doi.org/10.1021/la701324m (2007).
Mu, M. et al. Influence of surface roughness, nanostructure, and wetting on bacterial adhesion. Langmuir 39, 5426–5439. https://doi.org/10.1021/acs.langmuir.3c00091 (2023).
Unal, H., Sen, U. & Mimaroglu, A. Dry sliding wear characteristics of some industrial polymers against steel counterface. Tribol Int. 37, 727–732. https://doi.org/10.1016/j.triboint.2004.03.002 (2004).
Yousif, B. F., Alsofyani, I. M. & Yusaf, T. F. Adhesive wear and frictional characteristics of UHMWPE and HDPE sliding against different counterfaces under dry contact condition. Tribol. Mater. Surf. Interfaces 4, 78–85. https://doi.org/10.1179/175158310X12678019274408 (2010).
Aktas, C. et al. Force-based characterization of the wetting properties of LDPE surfaces treated with CF4 and H2 plasmas. Polymers 15, 2132. https://doi.org/10.3390/polym15092132 (2023).
Wang, S. et al. Two-step heat fusion kinetics and mechanical performance of thermoplastic interfaces. Sci. Rep. 12, 95573. https://doi.org/10.1038/s41598-022-09573-3 (2022).
Le, A. D. et al. Investigating the effect of interface temperature on molecular interdiffusion during laser transmission welding of 3D-printed composite parts. Materials 16, 6121. https://doi.org/10.3390/ma16186121 (2023).
Lee, J. U. & Hong, J. Y. Comparison of surface modification methods for improving the compatibility of recycled plastic film-based aggregates. Polymers 13, 3956. https://doi.org/10.3390/polym13223956 (2021).
Acknowledgements
Not applicable.
Funding
This research was funded by the Fujian Natural Science Foundation Project (grant numbers 2023J05252 and 2023J011406), and the Science and technology projects of Fujian Province (grant number 2023H4019 and 2024H4007), and the Science and technology key projects of Fuzhou city (grant number 2025-ZD-026).
Author information
Authors and Affiliations
Contributions
Conceptualization, D.C.; methodology, W.-J.Y. and D.C.; software, W.-J.Y.; validation, W.-J.Y.; formal analysis, D.C.; investigation, D.C.; resources, W.-J.Y.; data curation, W.-J.Y.; writing—original draft preparation, D.C. and W.-J.Y.; writing—review and editing, W.-J.Y.; visualization, W.-J.Y.; project administration, W.-J.Y.; funding acquisition, W.-J.Y.All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License, which permits any non-commercial use, sharing, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if you modified the licensed material. You do not have permission under this licence to share adapted material derived from this article or parts of it. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by-nc-nd/4.0/.
About this article
Cite this article
Cheng, D., Yan, WJ. Controlled hot pressing for functional upcycling of waste polyethylene materials. Sci Rep (2026). https://doi.org/10.1038/s41598-026-42655-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-026-42655-0
